Star Wars Custom Of The Week: Nerf LMTD Ambab Phase-Pulse Blaster Rifle By PsyfoolRulez Customz

By Bespin refugee on 2022-09-25 in Custom Toys & Art


Nerf LMTD Ambab Phase-Pulse Blaster Rifle by PsyfoolRulez Customz

"Long overdue project....I was a bit underwhelemd with the Nerf LMTD Mando Amban Pulse-Phase blaster rifle out of the box...Feels a bit lightweight and also too short and stocky in the middle....But after repainting and doing some mods on it, definitely looking much better and display-worthy.....Will be going through all the mods and detailing done to this blaster in my next post....



Some have asked if I dismantled my blasters for painting....I used to do that years ago....Definitely recommended to do this as it would make painting each part easier and you can get to all the hard to reach areas....However, you need to be very careful when dismantling and make sure you take lots of photos for each step and make sure you don't lose any of the parts, especially springs and screws....Assembly will also be challenging and there were times my blasters dont work properly after putting back together....😓....So now I dont take the risk and spray my blasters in one piece, masking individual parts as I go along......More tedious but lesser risk.....😅
First off, I sanded down all the raised wordings on the blaster with rough sandpaper and then going over with a smoother grit....I also covered all the screw holes on the left side of blaster (except for battery cover)....I do this by using thin sheets of styrene to overlay the holes instead of filling them up....I find this method easier...Did this for all of the holes except for the screw hole on the round bar below the barrel...Still went with filling for that one....Then I gave the whole blaster a coat of Krylon Grey primer before painting on the various colors...I used Krylon Oil Rubbed Bronze for the dark parts, Marabu matt gold for the scope mounts, Tamiya TS-38 gun metal for the body and Marabu gloss silver for the prongs....The burnt look was achieved by rubbing Tamiya Weathering Master kit....For the barrel clamps, I used aluminium foil tape instead of painting.....It gives a much more realistic metal feel to the blaster....
Besides the paintjob, there were two mods that I had to do to improve the overall look of the blaster....First is to mod the scope...The stock scope has no lenses on either ends (a big no-no!) and has a lighted targeting sight placed at the centre....I made two mock lenses...For the front, I used dark solar film to overlay a piece of round clear plastic and glued in place....for the rear, I used a round clear lens instead...This is to allow the targetting sight to still be visible...
The next mod was to come up with the missing scope mount leg....The Amban blaster scope should have two scope legs but the Nerf blaster has only one to allow the priming slider to slide forward....This missing leg bothers me right from the beginning and I have been thinking how to do it and still allow the blaster to shoot....So in the end I came up with a simple solution by fabricating the scope leg out of 5mm PVC board and simply jamming it in between the scope and blaster body.....This piece is removable to allow the blaster to shoot but most times, it would be just for display and it can stay in place....May not be the best solution so do share if you have other ideas.....😉
"



Check out more images of their custom below in our GALLERY!

If you would like to submit your own custom figure(s) to be displayed on JediInsider.com, be sure to check out our Custom Forum section, where you can discuss and show off your work among other customizers.
Image 1 of 35
1 of 35
Image 2 of 35
2 of 35
Image 3 of 35
3 of 35
Image 4 of 35
4 of 35
Image 5 of 35
5 of 35
Image 6 of 35
6 of 35
Image 7 of 35
7 of 35
Image 8 of 35
8 of 35
Image 9 of 35
9 of 35
Image 10 of 35
10 of 35
Image 11 of 35
11 of 35
Image 12 of 35
12 of 35
Image 13 of 35
13 of 35
Image 14 of 35
14 of 35
Image 15 of 35
15 of 35
Image 16 of 35
16 of 35
Image 17 of 35
17 of 35
Image 18 of 35
18 of 35
Image 19 of 35
19 of 35
Image 20 of 35
20 of 35
Image 21 of 35
21 of 35
Image 22 of 35
22 of 35
Image 23 of 35
23 of 35
Image 24 of 35
24 of 35
Image 25 of 35
25 of 35
Image 26 of 35
26 of 35
Image 27 of 35
27 of 35
Image 28 of 35
28 of 35
Image 29 of 35
29 of 35
Image 30 of 35
30 of 35
Image 31 of 35
31 of 35
Image 32 of 35
32 of 35
Image 33 of 35
33 of 35
Image 34 of 35
34 of 35
Image 35 of 35
35 of 35

STAR WARS SHOPPING ONLINE


Advertise Here on JediInsider.com

Search Online Stores for Star Wars custom



The affiliate links on this site may generate revenue for it when a purchase is made
Toys Shopping Oniine




Member Comments

~ NO COMMENTS YET ~
start the coversation with yours

ADD YOUR COMMENT NOW
(Membership Required)




More Star Wars News




Advertise on Jedi Insider


STAR WARS REVIEWS

Toy Photography

Movies & TV

Customs

Games



This site uses cookies for site configuration, advertising, and analysis. By using this site you accept our policies - Read Full Site Policy OK
Sign Up For The TNI Newsletter And Have The News Delivered To You!
SOCIAL NETWORKS

ToyNewsI MarvelousNews Tformers JediInsider
Entertainment News International (ENI) is the oldest, largest, and most popular news source for adult toy collectors (kidults) all around the world.

Get the scoop every day on all the popular culture action figures, comics, games, movies, toys, and more!

Contact and Support
Advertising | Submit News | Contact ENI | Privacy Policy


All images, trademarks, logos, video, brands and images used on this website are registered trademarks of their respective companies and owners. All Rights Reserved. Data has been shared for news reporting purposes only. All content sourced by fans, online websites, and or other fan community sources. Entertainment News International is not responsible for reporting errors, inaccuracies, omissions, and or other liablities related to news shared here. We do our best to keep tabs on infringements. If some of your content was shared by accident. Please Contact us about any infringements right away - CLICK HERE